TP-Link EAP673 AX5400 Wi-Fi 6 Ceiling Access Point

Give demanding workspaces room to connect The TP-Link EAP673 brings high-capacity Wi-Fi 6 to offices, meeting spaces and shared working areas without a bulky installation. Its AX5400 dual-band radios connect to a 2.5GbE wired uplink, helping a well-planned network serve capable wireless clients without immediately falling back to a Gigabit backhaul. A slim ceiling-mounted enclosure, PoE+ power and optional Omada management keep the installation discreet and the network manageable. Highlights Wireless capacity with a faster uplink Wi-Fi 6 with up to 4804Mbps on 5GHz and 574Mbps on 2.4GHz. One 2.5GbE Ethernet port and support for 160MHz channels. A discreet installation Low-profile ceiling or wall mounting with mounting hardware supplied. IEEE 802.3at PoE+ or 12V DC power; power adapter not included. A network you can manage Standalone operation or compatible Omada controller management. Guest access, VLAN mapping and supported controller-assisted roaming. Key Features Make the wired connection part of the plan A fast radio needs an appropriate connection back to the network. The 2.5GbE port gives the EAP673 more uplink headroom than a Gigabit-only access point when paired with a compatible switch and suitable cabling. It also negotiates with supported slower Ethernet links, so a site can upgrade its switching in stages. The broadband service, gateway and other traffic still determine the speed available to users. Use Wi-Fi 6 where it makes a difference OFDMA and MU-MIMO help supported devices share airtime more effectively. The 5GHz radio supports four spatial streams, while 2.4GHz provides two. A capable client can use the available channel width and modulation, but adding the two advertised band rates does not describe one device’s throughput. Choose channels after checking nearby networks, client support and local radio regulations. Keep the room focused on the work The 32.5mm-deep design sits close to a ceiling or wall. Power over Ethernet carries data and power on one cable, which helps keep adapters away from the occupied space. Use an IEEE 802.3at PoE+ source with enough budget for the installation, or the specified 12V/2A DC supply. A power adapter is not included with this model. Bring several access points under one view Use a compatible Omada hardware, software or cloud-based controller when the site needs central configuration and monitoring. Supported roaming, mesh and guest-portal functions depend on the controller, firmware and clients. Standalone management remains available for a simpler deployment. This is an access point for an existing network, rather than a replacement for the internet gateway. Give visitors an appropriate level of access Multiple SSIDs, SSID-to-VLAN mapping, client isolation and supported WPA security modes help organise wireless access. Match these settings to the switching and gateway configuration so guest devices have the intended route and permissions. WPA3 and enterprise authentication are useful options when the connected devices and wider network support them. Size the installation for real activity The manufacturer’s 250+ client reference describes association capacity under stated conditions, rather than a promise that every connected device can run a demanding application simultaneously. Consider concurrent calls, uploads and working distances. A coverage survey and a test with the actual client mix give a more useful result than choosing access-point quantity from a headline area figure alone. Summary Choose the EAP673 for an indoor business network that can benefit from Wi-Fi 6 capacity and a 2.5GbE uplink in a restrained ceiling design. Pair the radio, switching and power source deliberately, then use Omada management when the site needs coordinated control across several devices. Frequently Asked Questions Is EAP673 the same as EAP673-Extender?ExpandCollapse No. EAP673 is a ceiling or wall-mounted access point with a 2.5GbE uplink. EAP673-Extender is a separate product with a different installation format. Choose the exact model for the cable route and intended deployment. Is a power adapter included?ExpandCollapse No. Power the EAP673 from a compatible IEEE 802.3at PoE+ switch or injector, or use the specified 12V/2A DC supply purchased separately. Do I need a 2.5GbE switch?ExpandCollapse A 2.5GbE switch is needed to use the full wired uplink speed. The port can also negotiate supported slower Ethernet links, but those links limit aggregate traffic back to the network. Can it work without an Omada controller?ExpandCollapse Yes. Standalone management is supported. A compatible controller is required for supported centralised cloud access, coordinated roaming, mesh and guest-portal features. Does AX5400 mean one device gets 5400Mbps?ExpandCollapse No. AX5400 is a combined wireless class across separate radios. Actual throughput depends on the client, channel width, interference, distance and wired network. The advertised figures are signalling rates. Read more