Insta360 Rear View Mirror Mount
A Compact Camera Position for the Open Road Give a compatible camera a defined position on a suitable motorcycle or scooter mirror stem. Insta360 Rear View Mirror Mount uses an adjustable clamp for 6–15 mm mounting diameters and a ball-head arrangement for setting the recording angle. Its compact construction keeps the setup focused on the camera, rather than a long extension. Measure the stem, select the correct spacer and check clearance around the mirror and controls before recording on suitable roads. Highlights For suitable motorcycle and scooter mirror-stem installations. Clamping range of 6–15 mm. Use the correct spacer for 6–14 mm stems; 15 mm fits without one. Adjustable camera angle through the locking ball-head arrangement. Camera-only mounting; no selfie stick or extension pole. For suitable roads below 80 km/h; not off-road use. Key Features Measure the Stem Before Choosing the Mount The specified clamping range is 6–15 mm. For stems between 6 and 14 mm, select the corresponding spacer; a 15 mm stem can be clamped without one. Check the shape, accessible mounting area and complete installation rather than assuming that the diameter alone establishes suitability. Set the View Before the Ride The adjustable joint lets you prepare a useful camera angle before moving. Position the camera so that the mount does not obstruct the mirror, controls or the rider’s view, then lock the assembly and check it for movement. Make a short recording to assess framing before the main journey. Keep the Camera Directly on the Mount The manufacturer specifies a camera-only connection. Do not attach a selfie stick, extension pole or another accessory that increases the lever arm. Use the intended interface for a supported camera and check all connections; a compact direct setup is central to how this mount is meant to be used. Match the Riding Conditions Use the mount on suitable roads at speeds below 80 km/h, following the manufacturer’s instructions and the rules applicable to the location. It is not intended for off-road riding. The clamp’s fit does not establish that every vehicle, surface or riding condition is appropriate. A Small Accessory with Defined Dimensions The mount measures 40.2 × 48.5 × 89 mm and weighs approximately 82.6 g. These dimensions describe the mount rather than the full assembly with a camera. Allow room for the camera body, lens view, cable-free movement of the controls and normal mirror adjustment when planning the installation. Summary Choose Rear View Mirror Mount when a suitable mirror stem provides the right camera position. Confirm the diameter and spacer, attach only the supported camera arrangement and set the angle before riding. Keep the installation within the stated road and speed limits, with the mirror and controls clear. Frequently Asked Questions What Diameter Can It Clamp?ExpandCollapse The specified range is 6–15 mm. Use the corresponding spacer for a 6–14 mm mirror stem. For a 15 mm stem, no spacer is required. Check the available mounting area and do not force an unsuitable spacer onto the stem. Can I Add a Selfie Stick or Extension Pole?ExpandCollapse No. The manufacturer specifies that the mount connects only to a camera, without a selfie stick, extension pole or similar additional accessory. Do not treat the mounting point as approval for a longer or heavier arrangement. Is It Suitable for Off-Road Riding?ExpandCollapse No. The intended use is on suitable roads at speeds below 80 km/h. Follow the manufacturer instructions and the rules applicable to the location. Stop using the setup if the mount, camera or fittings move or loosen. Which Cameras Can I Use?ExpandCollapse Use a manufacturer-listed compatible camera with its intended mounting interface. Manufacturer-listed compatible models include X6, X5, X4 Air, Ace Pro 2, GO Ultra and GO 3S. Compatibility does not remove the camera-only mounting restriction. How Large and Heavy Is the Mount?ExpandCollapse The manufacturer states 40.2 × 48.5 × 89 mm and approximately 82.6 g. Allow additional space for the camera and confirm that the fitted assembly preserves the mirror’s function, normal control operation and the rider’s visibility.
Pickup available at 3005, Ubi Avenue 3, #01-88
Usually ready in 2-4 Business Day (Excluding Public Holiday)
Insta360 Rear View Mirror Mount
Description
A Compact Camera Position for the Open Road
Give a compatible camera a defined position on a suitable motorcycle or scooter mirror stem. Insta360 Rear View Mirror Mount uses an adjustable clamp for 6–15 mm mounting diameters and a ball-head arrangement for setting the recording angle. Its compact construction keeps the setup focused on the camera, rather than a long extension. Measure the stem, select the correct spacer and check clearance around the mirror and controls before recording on suitable roads.
Highlights
- For suitable motorcycle and scooter mirror-stem installations.
- Clamping range of 6–15 mm.
- Use the correct spacer for 6–14 mm stems; 15 mm fits without one.
- Adjustable camera angle through the locking ball-head arrangement.
- Camera-only mounting; no selfie stick or extension pole.
- For suitable roads below 80 km/h; not off-road use.
Key Features
Measure the Stem Before Choosing the Mount
The specified clamping range is 6–15 mm. For stems between 6 and 14 mm, select the corresponding spacer; a 15 mm stem can be clamped without one. Check the shape, accessible mounting area and complete installation rather than assuming that the diameter alone establishes suitability.
Set the View Before the Ride
The adjustable joint lets you prepare a useful camera angle before moving. Position the camera so that the mount does not obstruct the mirror, controls or the rider’s view, then lock the assembly and check it for movement. Make a short recording to assess framing before the main journey.
Keep the Camera Directly on the Mount
The manufacturer specifies a camera-only connection. Do not attach a selfie stick, extension pole or another accessory that increases the lever arm. Use the intended interface for a supported camera and check all connections; a compact direct setup is central to how this mount is meant to be used.
Match the Riding Conditions
Use the mount on suitable roads at speeds below 80 km/h, following the manufacturer’s instructions and the rules applicable to the location. It is not intended for off-road riding. The clamp’s fit does not establish that every vehicle, surface or riding condition is appropriate.
A Small Accessory with Defined Dimensions
The mount measures 40.2 × 48.5 × 89 mm and weighs approximately 82.6 g. These dimensions describe the mount rather than the full assembly with a camera. Allow room for the camera body, lens view, cable-free movement of the controls and normal mirror adjustment when planning the installation.
Summary
Choose Rear View Mirror Mount when a suitable mirror stem provides the right camera position. Confirm the diameter and spacer, attach only the supported camera arrangement and set the angle before riding. Keep the installation within the stated road and speed limits, with the mirror and controls clear.
Frequently Asked Questions
What Diameter Can It Clamp?
The specified range is 6–15 mm. Use the corresponding spacer for a 6–14 mm mirror stem. For a 15 mm stem, no spacer is required. Check the available mounting area and do not force an unsuitable spacer onto the stem.
Can I Add a Selfie Stick or Extension Pole?
No. The manufacturer specifies that the mount connects only to a camera, without a selfie stick, extension pole or similar additional accessory. Do not treat the mounting point as approval for a longer or heavier arrangement.
Is It Suitable for Off-Road Riding?
No. The intended use is on suitable roads at speeds below 80 km/h. Follow the manufacturer instructions and the rules applicable to the location. Stop using the setup if the mount, camera or fittings move or loosen.
Which Cameras Can I Use?
Use a manufacturer-listed compatible camera with its intended mounting interface. Manufacturer-listed compatible models include X6, X5, X4 Air, Ace Pro 2, GO Ultra and GO 3S. Compatibility does not remove the camera-only mounting restriction.
How Large and Heavy Is the Mount?
The manufacturer states 40.2 × 48.5 × 89 mm and approximately 82.6 g. Allow additional space for the camera and confirm that the fitted assembly preserves the mirror’s function, normal control operation and the rider’s visibility.
Specs
Insta360 Rear View Mirror Mount
Insta360 Rear View Mirror Mount is a compact adjustable camera support for suitable motorcycle and scooter mirror stems. The clamp diameter, spacer selection and riding limits must be checked together. The stated size and weight describe the mount, not the combined camera installation. Use only the intended direct-camera arrangement and position it clear of the mirror, controls and normal vehicle operation. A fitting that clamps securely still requires the correct camera interface and a suitable road environment.
| Specification | Details |
|---|---|
| Clamp and Position | |
| Application | Suitable motorcycle or scooter rear-view mirror stem |
| Clamping Diameter | 6–15 mm |
| Spacer Selection | Matching spacer for 6–14 mm; no spacer for 15 mm |
| Angle Setting | Adjustable locking ball-head arrangement |
| Camera and Use Limits | |
| Camera Connection | Camera only, with the intended compatible interface |
| Additional Extensions | Selfie sticks, extension poles and other accessory extensions are not supported |
| Riding Environment | Suitable roads; not off-road |
| Speed Guidance | Below 80 km/h, with all applicable local restrictions observed |
| Physical Design | |
| Dimensions | 40.2 × 48.5 × 89 mm |
| Weight | Approximately 82.6 g |
| Clearance Check | Allow for the camera, mirror, controls and rider visibility |
| Package and Preparation | |
| Included | Rear View Mirror Mount and supplied installation/spacer components shown in the product photographs |
| Separate Equipment | Camera and vehicle |
| Before Use | Measure the stem, select the correct spacer, lock the angle and check all fittings |