Insta360 GO Ultra Quick Release Mount

Change the View with a Secure Connection Move your GO Ultra setup between compatible mounting positions with a camera-specific quick-release connection. Insta360 GO Ultra Quick Release Mount combines magnetic alignment with two locking buckles and supports both the Standalone Camera and Action Pod. The included adapters connect the mount to suitable 1/4-inch and prong-based accessories, while its angled design helps with camera positioning. It is the dedicated GO Ultra mount, rather than a universal quick-release accessory for every camera. Highlights Fits the GO Ultra Standalone Camera and Action Pod. Magnetic alignment plus locking buckles on both sides. Angled two-prong design for camera-position adjustment. Includes 1/4-inch to 3-Prong and 2-Prong to 3-Prong adapters. Supplied with one long thumb screw and four anti-slip rings. Key Features Mount the Camera or the Action Pod Use the same dedicated mount for the GO Ultra Standalone Camera or its Action Pod. Align the camera mark, press the unit fully into place and confirm that both side buckles have locked. This lets you choose the camera configuration for the shot without assuming that another GO generation uses the same mounting interface. Combine Magnetic Alignment with a Mechanical Lock Magnets help position the supported camera, while the side buckles provide the locking connection. Check both sides before moving and avoid relying on magnetic attraction alone. To remove the camera or Action Pod, support it, press and hold both release buckles, then lift it from the mount. Connect to Suitable Camera Accessories The package includes a 1/4-inch to 3-Prong Adapter and a 2-Prong to 3-Prong Adapter, with a long thumb screw for assembly. These give you practical connection options for suitable selfie sticks and other camera mounts. Check the complete accessory’s load, activity and installation instructions; a matching thread alone does not establish that every setup is appropriate. Refine the Angle and Connection The tilted two-prong arrangement helps position the camera for supported filming setups. If the adapter connection feels loose, use the supplied anti-slip rings as instructed and recheck the joint. The silicone pad helps reduce unwanted contact noise during active use when fitted firmly; it does not remove wind noise or make the recording silent. Keep the Kit Focused on the Right Camera This compact accessory is designed specifically for GO Ultra’s connection. It is different from the general Quick Release Mount 2.0 and the GO 3/GO 3S mount. The camera, Action Pod, selfie stick and other illustrated mounts are separate. Keep each connection clean, check the locking action and prepare a short test before an important session. Summary Insta360 GO Ultra Quick Release Mount provides a dedicated magnetic-and-buckle connection for changing between compatible camera setups. Its supplied adapters, screw and anti-slip rings make it practical to assemble the intended mounting arrangement. Match the accessory and activity, confirm both locking buckles and keep the complete camera setup secure. Frequently Asked Questions Does It Fit Both the Camera and the Action Pod?ExpandCollapse Yes. It accepts the Insta360 GO Ultra Standalone Camera and GO Ultra Action Pod. Align the camera mark and confirm that both side buckles lock fully before use. Is This the Same as Quick Release Mount 2.0?ExpandCollapse No. This accessory has the dedicated GO Ultra connection. Do not substitute it for the general Quick Release Mount 2.0 or the GO 3/GO 3S mount solely because the names are similar. Which Parts Are Included?ExpandCollapse The package contains one Quick Release Mount, one 1/4-inch to 3-Prong Adapter, one 2-Prong to 3-Prong Adapter, one long thumb screw and four anti-slip rings. Camera, Action Pod, selfie stick and other mounts are separate. How Do I Release the Camera?ExpandCollapse Support the camera or Action Pod, then press and hold both buckles on the mount before lifting it away. To reattach, align the camera mark, press it fully into the mount and confirm both buckles have locked. What If an Adapter Connection Feels Loose?ExpandCollapse Fit the supplied anti-slip rings to the adapter connection as instructed, then reassemble and check the joint. Use the supplied silicone pad correctly and inspect the complete setup before recording. Follow the activity and load limits of every connected accessory. Read more