Insta360 GO 3/GO 3S Dive Case

Take the complete GO setup beneath the surface The Insta360 GO 3/GO 3S Dive Case encloses a compatible camera and Action Pod for underwater recording down to 60 m. A clear optical glass window, secure buckle and accessible external controls create a purpose-built arrangement for diving and underwater stories. Supplied anti-fog inserts and mounting accessories help you prepare the setup, while the compact housing lets you retain the Action Pod rather than using the tiny camera alone. Highlights Purpose-built housing for Insta360 GO 3 or GO 3S with its Action Pod. Maximum underwater depth of 60 m when correctly assembled and sealed. Hydrophobic, oil-resistant optical glass window for underwater filming. Buckle closure with external shutter, power and Q controls. Includes anti-fog inserts, wrist strap, protective pouch and mounting accessories. Key Features Bring the Action Pod underwater The Action Pod is not designed for unprotected submersion, so this housing provides a dedicated way to take the camera-and-Pod assembly underwater. Align the lens and controls correctly before closing the case. The current housing supports both GO 3 and GO 3S, with the camera equipment sold separately. Purpose-built for dives to 60 m A rigid plastic housing and maintained rubber seal protect the assembled setup to the specified maximum depth. Before each outing, inspect the seal and perform the recommended empty-case leak test. Keep grit, hair and other debris away from the sealing surfaces so the buckle can close properly. A clear optical window The glass window has hydrophobic and oil-resistant properties to help maintain a clear view. Keep the exterior clean and position the supplied anti-fog inserts as instructed inside the housing. Oversized replacement inserts can interfere with the seal, so correct preparation matters as much as the housing itself. Controls designed for the closed case External shutter, power and Q controls let you operate the camera through the sealed housing. The buckle uses a locking lever for deliberate opening and closing. Check that the buckle clicks into place and that the controls align with the camera before entering the water. Mounting accessories for a complete arrangement The supplied thumb screw, anti-slip rings and 3-Prong to 1/4-inch Adapter support attachment to suitable underwater accessories. A wrist strap adds a retention option, and the protective pouch helps organise the housing between uses. Floating grips and other equipment shown in examples are sold separately. Care that supports repeat use After saltwater use, follow the cleaning routine: remove the camera only when the case exterior is dry, then close and soak the empty housing in fresh water before a gentle rinse. Avoid pressure jets, solvents and heat drying. Let the housing dry fully before storing it. Summary The Insta360 GO 3/GO 3S Dive Case extends the camera-and-Action-Pod setup to properly prepared underwater recording. Its 60 m rating, glass window and accessible controls are complemented by the supplied anti-fog and mounting accessories. Inspect, test and maintain the housing before each use, and use it only within the stated limits. Frequently Asked Questions Does this case fit both GO 3 and GO 3S?ExpandCollapse Yes. The current manufacturer housing is specified for GO 3 and GO 3S, with the camera inserted in its Action Pod. It is not the GO Ultra Dive Case. The camera and Action Pod are sold separately. How deep can I use it?ExpandCollapse The maximum specified depth is 60 m with the camera and Action Pod installed and the housing correctly sealed. Before use, test the closed empty case in water for three minutes and check inside for moisture. Do not take the empty housing deeper than 30 m. Are anti-fog inserts included?ExpandCollapse Yes, six anti-fog inserts are supplied. Fit them in the illustrated positions and keep them clear of the seal. Third-party replacements must be no larger than 28 × 15 × 1.2 mm; oversized inserts can stop the case sealing correctly. Can I attach a floating grip or other mount?ExpandCollapse Yes, the kit includes a 3-Prong to 1/4-inch Adapter, thumb screw and anti-slip rings for suitable accessory connections. Floating grips and other separate mounts are not included. Use the wrist strap and check every connection before entering the water. How should I clean it after seawater use?ExpandCollapse Do not open the housing while it is wet. Once the exterior is dry and the camera has been removed, close the empty case and soak it in fresh water for five to ten minutes, then rinse gently and dry with a soft cloth. Avoid pressure jets, detergent, alcohol and heat drying. 阅读更多