Insta360 Bike Kit

Two Perspectives For Your Next Ride The Insta360 Bike Kit combines a Handlebar Mount and Chest Strap, giving you two practical ways to record the same journey. Position a compatible camera directly on the bike or wear it for an immersive view that follows your movement. Supplied adapters, anti-slip rings and thumb screws support the intended connections, with clear fit and load limits for each mounting method. Highlights Includes a Handlebar Mount and a padded, adjustable Chest Strap Ball-joint handlebar arrangement for adjusting the camera angle Tube fit depends on whether the rubber insert is installed Separate camera limits of 300g on the handlebar mount and 250g on the chest strap Includes mounting adapters, anti-slip rings, an extension and thumb screws Key Features Frame The Journey From The Bike The Handlebar Mount uses a ball joint to help position the camera, with a direct camera connection required. Mount it only to a suitable handlebar or seat post. It is not approved for a selfie stick or additional extension, even though the kit includes a separate Mount Extension among its fittings. A View That Follows Your Movement The Chest Strap uses soft padding and adjustable straps to establish a close, comfortable fit for first-person footage. Position the camera where it has a clear view and confirm that the strap sits securely before riding. Its camera-weight limit is 250g, which is lower than the separate Handlebar Mount limit. Choose The Right Tube Fit With the rubber insert fitted, the Handlebar Mount supports tubes from 8mm to 16mm in diameter. Without the insert, the specified range is 22mm to 35mm. These are separate supported ranges, so measure the attachment point and use the configuration that fits it correctly rather than assuming every diameter between them is covered. Keep The Camera And Route Within Scope The Handlebar Mount supports a camera up to 300g, while the Chest Strap supports up to 250g. Insta360 recommends a maximum of 60km/h on even surfaces for both and says to avoid uneven or bumpy surfaces. Select the mounting method and route accordingly, with no improvised extensions or modifications. The Fittings For A Coordinated Setup Four anti-slip rings, two camera-interface adapters, a Mount Extension and four thumb screws are supplied alongside the two mounts. Use the appropriate adapter for the camera and follow the mounting instructions. GO 3 and GO 3S require a compatible Quick Release Mount; GO Ultra also needs an appropriate compatible interface, such as its Magnetic Mount or Action Mount, where required and sold separately. Summary The Bike Kit brings bike-mounted and chest-mounted views into one coordinated accessory set. It suits riders who want to change perspective while keeping the camera connection simple, with the correct tube fit, load limit and even-surface riding conditions checked before use. Frequently Asked Questions Can I Add A Selfie Stick To The Handlebar Mount?ExpandCollapse No. The Handlebar Mount must connect directly to the camera and must not be used with a selfie stick or other extension. The kit includes a Mount Extension, but that does not remove the direct-camera restriction for the Handlebar Mount. What Tube Sizes Does The Handlebar Mount Fit?ExpandCollapse With its rubber insert, the supported diameter is 8–16mm. Without the insert, it supports 22–35mm. Use it only on an appropriate handlebar or seat post and select the configuration that correctly fits the measured tube. What Camera Weight And Speed Are Allowed?ExpandCollapse The Handlebar Mount has a 300g camera limit and the Chest Strap has a 250g limit. Insta360 recommends up to 60km/h on even surfaces for both and says to avoid uneven or bumpy surfaces. Do GO-Series Cameras Need An Additional Mount?ExpandCollapse GO 3 and GO 3S require their compatible Quick Release Mount. For GO Ultra, use the appropriate manufacturer-approved camera interface, such as its Magnetic Mount or Action Mount where required. Camera-specific mounts are sold separately unless explicitly listed in the kit contents. What Comes In The Box?ExpandCollapse One Handlebar Mount, one Chest Strap, four anti-slip rings, one Mount Extension, one 1/4-inch-to-two-prong adapter, one 1/4-inch-to-three-prong adapter and four thumb screws are included. The camera and any separate model-specific mounting accessory are not included. 阅读更多