Ubiquiti UA-G3-SK-Elevator G3 Elevator Access Starter Kit
Make Floor Access Part of the Arrival Experience Bring authorised floor selection into a UniFi Access installation with the G3 Elevator Starter Kit. It combines an 18-relay elevator hub, a G3 Reader, a pair of 2-wire PoE extenders and access cards. The kit provides the hardware foundation for a planned lift-access integration, with inputs for car status and emergency signals alongside reader connectivity. Highlights Control Authorised Floors 18 relay outputs for supported floor-selection integration. Inputs for emergency, car position, movement and door status. A Coordinated Starter Set Elevator Hub and G3 Reader included. Two 2-wire PoE extenders and 10 Access Cards. Networked Management Managed through UniFi Access. PoE++ input with a shared PoE output budget for connected devices. Key Features Connect Permissions to Floor Selection The elevator hub provides 18 low-voltage relay outputs for a supported floor-selection design. UniFi Access manages the configured permissions, helping the reader interaction correspond to the authorised destination. The actual interface must be agreed with the lift system and its responsible installation team. Start With a Complete Core Kit The box includes an Elevator Hub, one G3 Reader, two 2-wire PoE extenders and 10 Access Cards. These are the core access components rather than an entire lift installation. A suitable PoE++ power source, the required cables and any site-specific integration hardware are selected separately. Give Existing Cabling a Considered Role The included extender pair provides a 2-wire PoE transport option for a suitable cable route. Cable type, length and power delivery need to be checked against the installation guide. A reader can then be positioned within the planned system without assuming every existing lift cable is suitable. Read Credentials at the Car The included G3 Reader supports NFC and compatible mobile access methods. Its proximity sensing and user feedback provide a clear point for credential presentation. Credential support and any Touch Pass entitlement depend on the configured UniFi system and the applicable service terms. Keep System Status Visible Dedicated inputs cover emergency signals, five-bit car position, up/down/stop/full status and door open/close status. These inputs support the intended access integration. They must not replace or bypass the lift’s approved safety controls, emergency operation or maintenance procedures. Plan the Power and Relay Limits The hub accepts PoE++ and provides four PoE+ outputs with a 45 W shared maximum. Each of its 18 relays is rated 30 V DC at 2 A. Treat these as specified control interfaces and have a qualified lift/access Specialist check the design before installation. Summary The G3 Elevator Starter Kit brings the principal UniFi access components together for a planned floor-control integration. It suits projects that need credential-based floor permissions, clear system inputs and a coordinated reader connection, with the lift interface and installation scope confirmed separately. Frequently Asked Questions How Many Floors Can It Control?ExpandCollapse The hub has 18 relay outputs for supported floor-selection integration. The usable arrangement depends on the lift interface and the approved system design. What Is Included?ExpandCollapse One Elevator Hub, one G3 Reader, two 2-wire PoE extenders and 10 Access Cards. Power sourcing, site cabling and installation are separate requirements. Does It Include the PoE++ Power Source?ExpandCollapse A suitable PoE++ source is required separately. The hub has a 45 W shared output budget, with individual PoE+ ports rated up to 30 W within that total. Can It Reuse Existing Lift Cabling?ExpandCollapse The extender pair provides a supported 2-wire PoE option. The cable route, conductor requirements, distance and available power must be checked before reuse. Can It Be Fitted to Any Lift Without Design Work?ExpandCollapse No universal lift compatibility is claimed. The responsible lift/access Specialist must confirm the interface, relay ratings, emergency operation and approved installation method.
追加商品 (2)
3005, Ubi Avenue 3, #01-88で受け取り可能
通常2〜4日で準備が完了します
Ubiquiti UA-G3-SK-Elevator G3 Elevator Access Starter Kit
商品説明
Make Floor Access Part of the Arrival Experience
Bring authorised floor selection into a UniFi Access installation with the G3 Elevator Starter Kit. It combines an 18-relay elevator hub, a G3 Reader, a pair of 2-wire PoE extenders and access cards. The kit provides the hardware foundation for a planned lift-access integration, with inputs for car status and emergency signals alongside reader connectivity.
Highlights
Control Authorised Floors
- 18 relay outputs for supported floor-selection integration.
- Inputs for emergency, car position, movement and door status.
A Coordinated Starter Set
- Elevator Hub and G3 Reader included.
- Two 2-wire PoE extenders and 10 Access Cards.
Networked Management
- Managed through UniFi Access.
- PoE++ input with a shared PoE output budget for connected devices.
Key Features
Connect Permissions to Floor Selection
The elevator hub provides 18 low-voltage relay outputs for a supported floor-selection design. UniFi Access manages the configured permissions, helping the reader interaction correspond to the authorised destination. The actual interface must be agreed with the lift system and its responsible installation team.
Start With a Complete Core Kit
The box includes an Elevator Hub, one G3 Reader, two 2-wire PoE extenders and 10 Access Cards. These are the core access components rather than an entire lift installation. A suitable PoE++ power source, the required cables and any site-specific integration hardware are selected separately.
Give Existing Cabling a Considered Role
The included extender pair provides a 2-wire PoE transport option for a suitable cable route. Cable type, length and power delivery need to be checked against the installation guide. A reader can then be positioned within the planned system without assuming every existing lift cable is suitable.
Read Credentials at the Car
The included G3 Reader supports NFC and compatible mobile access methods. Its proximity sensing and user feedback provide a clear point for credential presentation. Credential support and any Touch Pass entitlement depend on the configured UniFi system and the applicable service terms.
Keep System Status Visible
Dedicated inputs cover emergency signals, five-bit car position, up/down/stop/full status and door open/close status. These inputs support the intended access integration. They must not replace or bypass the lift’s approved safety controls, emergency operation or maintenance procedures.
Plan the Power and Relay Limits
The hub accepts PoE++ and provides four PoE+ outputs with a 45 W shared maximum. Each of its 18 relays is rated 30 V DC at 2 A. Treat these as specified control interfaces and have a qualified lift/access Specialist check the design before installation.
Summary
The G3 Elevator Starter Kit brings the principal UniFi access components together for a planned floor-control integration. It suits projects that need credential-based floor permissions, clear system inputs and a coordinated reader connection, with the lift interface and installation scope confirmed separately.
Frequently Asked Questions
How Many Floors Can It Control?
The hub has 18 relay outputs for supported floor-selection integration. The usable arrangement depends on the lift interface and the approved system design.
What Is Included?
One Elevator Hub, one G3 Reader, two 2-wire PoE extenders and 10 Access Cards. Power sourcing, site cabling and installation are separate requirements.
Does It Include the PoE++ Power Source?
A suitable PoE++ source is required separately. The hub has a 45 W shared output budget, with individual PoE+ ports rated up to 30 W within that total.
Can It Reuse Existing Lift Cabling?
The extender pair provides a supported 2-wire PoE option. The cable route, conductor requirements, distance and available power must be checked before reuse.
Can It Be Fitted to Any Lift Without Design Work?
No universal lift compatibility is claimed. The responsible lift/access Specialist must confirm the interface, relay ratings, emergency operation and approved installation method.
仕様
Ubiquiti UA-G3-SK-Elevator G3 Elevator Access Starter Kit
The G3 Elevator Starter Kit combines an 18-relay UniFi Access elevator hub with a G3 Reader, a pair of 2-wire PoE extenders and access cards. It is intended for a planned floor-selection integration with a compatible lift control interface. The specifications below separate hub capacity, power outputs and component requirements so the kit can be assessed as a complete system. Site cabling, the PoE++ source and the approved lift integration are separate installation requirements.
| Specification | Details |
|---|---|
| Kit and Access Control | |
| Included Components | Elevator Hub; G3 Reader; 2 × 2-wire PoE extenders; 10 Access Cards |
| Floor Control | 18 relay outputs; 30 V DC 2 A per relay |
| Hub User Capacity | Up to 6,000 users |
| Management | UniFi Access |
| System Inputs | Emergency; 5-bit car position; up/down/stop/full car status; door open/close |
| Hub Network and Power | |
| Network | 4 × GbE networking interfaces; dedicated GbE management interface |
| Power Input | PoE++ source required |
| PoE Outputs | 4 × PoE+; up to 30 W per port within 45 W shared total |
| Hub Consumption | 7 W maximum excluding PoE output |
| Hub Dimensions and Weight | 129.3 × 244.7 × 33.6 mm; 537 g |
| Reader and Extenders | |
| G3 Reader | NFC and compatible mobile access; BLE 4.1; 1 × 10/100 MbE PoE connection |
| Reader Power | 5 W maximum; 48 V DC PoE |
| Reader Dimensions and Weight | 93 × 40 × 36.5 mm; 82 g |
| Reader Environment | IP55; −30 to 45 °C; 5–90% non-condensing humidity |
| Extender Pair | 2-wire transport; PoE++ input and PoE+ output; 10/100 MbE interfaces |
| Extender Dimensions and Weight | 40 × 105 × 25 mm each; 77 g transmitter and 79 g receiver |
| Installation | |
| Hub and Extender Environment | −10 to 40 °C; 5–95% non-condensing humidity |
| Access Cards | 10 cards; 13.56 MHz MIFARE DESFire; ISO 7810 ID-1 format |
| Integration Requirement | Compatible lift control interface and approved low-voltage/safety design |




























