D-Link DEM-410T 10GBASE-T SFP+ Copper Transceiver

A Copper Connection for a Compatible 10GbE Slot The DEM-410T adds a 10GBASE-T connection to a compatible SFP+ host port. It is designed for short copper connections between supported network equipment. An RJ45 connection and 10 Gbps interface keep the required host and cable choice clear. The specified link reach is up to 30 m over Cat6A at 10Gbps. Match the switch’s supported module revision, port power and cooling requirements before installation. Highlights Connection Standard 10GBASE-T at 10 Gbps. SFP+ module with RJ45 connector. Up to 30 m over Cat6A at 10Gbps. Link Requirements Suitable Cat6A copper cable for 10Gbps operation. Electrical copper connection. Compatible host port and supported module revision required. Installation Hot-pluggable design in a supported host. Match both ends and test the completed link. 5-year warranty. Key Features Choose the Correct Host Interface This module uses the SFP+ form factor and the 10GBASE-T connection standard. Check the host’s exact compatibility list, supported speed and hardware revision. Similar-looking SFP, SFP+, QSFP+ and QSFP28 modules are not automatically interchangeable. Match the Cable to the Link Use a suitable Cat6A connection for the specified 10Gbps reach. A copper module does not extend a 10GbE link to the ordinary 100 m channel length of a native 10GBASE-T switch port. Cable quality and the host requirements remain important. Plan the Required Distance The published reach is up to 30 m over Cat6A at 10Gbps. This specification depends on suitable cable and supported host operation. Keep bend radius, termination quality and the actual link path within the cable and equipment requirements. Make Maintenance More Practical Hot-pluggable construction allows a supported host to accept or release the module without powering down the chassis. Removing the module still interrupts the link that uses it. Schedule the work and provide a tested alternate path where that connection is carrying production traffic. Check the Complete Pair The remote connection must support 10GBASE-T at the intended speed. Check auto-negotiation and host behaviour before using a different speed; do not assume every SFP+ port supports every copper module. Install Within the Host Limits The module operating range is 0°C to 65°C; host may impose a lower limit. Copper SFP+ modules add heat inside the host. Verify permitted port population and the host’s ambient-temperature limits, which may be more restrictive than the module’s own rating. For DGS-3630-28TC and DGS-3630-52PC, D-Link specifies hardware A2 only, at most two modules per switch and ambient temperature no higher than 40°C. Other hosts require their own compatibility check. Summary The DEM-410T provides a focused 10GBASE-T connection for a compatible SFP+ host. Specify the correct copper cable and host thermal limits with the module to build a link that suits the installation. Frequently Asked Questions Will It Work in Any Similar-Looking Slot?ExpandCollapse No. The host must explicitly support this SFP+ module, connection standard, speed and hardware revision. Check the switch or adapter compatibility list before ordering. For DGS-3630-28TC and DGS-3630-52PC, D-Link specifies hardware A2 only, at most two modules per switch and ambient temperature no higher than 40°C. Other hosts require their own compatibility check. Which Cable Does It Need?ExpandCollapse Use suitable Cat6A copper cabling. The cable and remote interface must match the connection standard. What Is the Maximum Link Distance?ExpandCollapse Up to 30 m over suitable Cat6A cabling at 10Gbps, within the supported host and installation limits. The host may impose additional temperature or port-population restrictions. Can It Be Fitted Without Turning Off the Switch?ExpandCollapse The module is hot-pluggable in a supported host. Fitting or removing it can still interrupt that link, so plan maintenance around the traffic it carries. Can It Replace a Different Optical Standard?ExpandCollapse Do not assume so. This is an electrical copper module, not a fibre optic module. Host compatibility, power and heat limits must be checked. Are Connection Cables Included?ExpandCollapse No connection cable is included. Select suitable Cat6A cabling separately and confirm the host-specific temperature and port-population restrictions for this copper SFP+ module. 続きを読む