D-Link DMC-700SC Gigabit Multimode SC Fibre Media Converter
Extend the Network Beyond the Copper Cable The DMC-700SC converts a copper Gigabit Ethernet connection to 1000BASE-SX multimode SC fibre. It keeps existing copper-connected equipment in the network while providing a fibre path suited to the required route. Its fixed optical interface provides a straightforward connection to the matching fibre system. Use it as a standalone converter with its supplied adapter, or follow the compatible DMC-1000 chassis installation instructions for a central rack installation. Fibre leads and the remote endpoint are selected for the complete link; this is a data converter rather than a PoE injector. Highlights Media Connection 1 × 1000BASE-T RJ-45 port. 1000BASE-SX multimode SC. 850 nm. Link Design Up to 550 m with suitable multimode fibre. Full-duplex Gigabit operation. Match the fibre type and connector at both ends. Installation 120 × 88 × 25 mm compact housing. Use the matched supplied external DC adapter. Standalone or documented DMC-1000 chassis installation. 5-year warranty. Key Features Keep Copper Equipment on a Fibre Route The 1000BASE-T interface connects the local Ethernet equipment using a compliant twisted-pair cable. The optical side then carries the connection over the selected fibre route. This can extend a network between suitable locations without requiring every endpoint to have its own built-in fibre interface. Choose the Correct Optical Path The fixed 1000BASE-SX multimode SC interface must connect to an appropriate fibre cable and matching remote device. Up to 550 m with suitable multimode fibre. Check the optical budget and connector losses for the route. Use Full-Duplex Gigabit Ethernet The converter supports a 1 Gbps link in each direction under the supported operating conditions. Manufacturer references to 2000 Mbps full-duplex transfer describe the aggregate of both directions, rather than a 2GbE port speed. The complete link is limited by its endpoints, selected media and cable installation. Install for the Size of the Site Start with a standalone unit and the correct external adapter. For a central installation, the documented DMC-1000 procedure removes the converter housing and mounts the board on the chassis carrier. Chassis compatibility and service instructions must match the exact converter configuration. See Link Status During Troubleshooting Power and link/activity indicators provide a quick local check during commissioning and service. Verify both copper and optical sides when diagnosing a missing connection. Supported link-loss functions can help carry a fault indication to the adjacent equipment when configured correctly. Complete the Connection Deliberately Select the fibre lead, remote endpoint and matched power adapter for the installation. Keep the converter within its specified environmental range and protect the fibre connectors from dust. It does not supply PoE power or replace the firewall and security controls on the surrounding network. Summary The DMC-700SC provides a compact bridge between copper Ethernet and the specified fibre interface. Match the media and remote endpoint, use the correct power adapter and test the complete link before putting it into service. Frequently Asked Questions Does It Include an Optical Transceiver?ExpandCollapse Its fixed optical interface is built in. Fibre patch leads and the matching remote endpoint are selected separately. What Fibre Does It Use?ExpandCollapse 1000BASE-SX multimode SC. 850 nm. How Far Can the Fibre Link Run?ExpandCollapse Up to 550 m with suitable multimode fibre. The complete optical budget includes cable, connectors, splices and the remote receiver. Does It Supply PoE?ExpandCollapse No. It carries Ethernet data without injecting PoE power. Power the endpoint separately or choose an appropriate separate PoE arrangement. Can It Be Installed in a Chassis?ExpandCollapse The manufacturer documents installation in the DMC-1000 chassis, following the board and carrier procedure for the exact converter. The chassis provides module power after installation. Which Power Adapter Should I Use?ExpandCollapse Use the matched supplied external DC adapter. Do not substitute an adapter based only on connector fit. Check the device label and supplied adapter voltage before connecting power.
3005, Ubi Avenue 3, #01-88에서 픽업 가능
일반적으로 2~4일 후 준비 완료
D-Link DMC-700SC Gigabit Multimode SC Fibre Media Converter
제품 설명
Extend the Network Beyond the Copper Cable
The DMC-700SC converts a copper Gigabit Ethernet connection to 1000BASE-SX multimode SC fibre. It keeps existing copper-connected equipment in the network while providing a fibre path suited to the required route. Its fixed optical interface provides a straightforward connection to the matching fibre system.
Use it as a standalone converter with its supplied adapter, or follow the compatible DMC-1000 chassis installation instructions for a central rack installation. Fibre leads and the remote endpoint are selected for the complete link; this is a data converter rather than a PoE injector.
Highlights
Media Connection
- 1 × 1000BASE-T RJ-45 port.
- 1000BASE-SX multimode SC.
- 850 nm.
Link Design
- Up to 550 m with suitable multimode fibre.
- Full-duplex Gigabit operation.
- Match the fibre type and connector at both ends.
Installation
- 120 × 88 × 25 mm compact housing.
- Use the matched supplied external DC adapter.
- Standalone or documented DMC-1000 chassis installation.
- 5-year warranty.
Key Features
Keep Copper Equipment on a Fibre Route
The 1000BASE-T interface connects the local Ethernet equipment using a compliant twisted-pair cable. The optical side then carries the connection over the selected fibre route. This can extend a network between suitable locations without requiring every endpoint to have its own built-in fibre interface.
Choose the Correct Optical Path
The fixed 1000BASE-SX multimode SC interface must connect to an appropriate fibre cable and matching remote device. Up to 550 m with suitable multimode fibre. Check the optical budget and connector losses for the route.
Use Full-Duplex Gigabit Ethernet
The converter supports a 1 Gbps link in each direction under the supported operating conditions. Manufacturer references to 2000 Mbps full-duplex transfer describe the aggregate of both directions, rather than a 2GbE port speed. The complete link is limited by its endpoints, selected media and cable installation.
Install for the Size of the Site
Start with a standalone unit and the correct external adapter. For a central installation, the documented DMC-1000 procedure removes the converter housing and mounts the board on the chassis carrier. Chassis compatibility and service instructions must match the exact converter configuration.
See Link Status During Troubleshooting
Power and link/activity indicators provide a quick local check during commissioning and service. Verify both copper and optical sides when diagnosing a missing connection. Supported link-loss functions can help carry a fault indication to the adjacent equipment when configured correctly.
Complete the Connection Deliberately
Select the fibre lead, remote endpoint and matched power adapter for the installation. Keep the converter within its specified environmental range and protect the fibre connectors from dust. It does not supply PoE power or replace the firewall and security controls on the surrounding network.
Summary
The DMC-700SC provides a compact bridge between copper Ethernet and the specified fibre interface. Match the media and remote endpoint, use the correct power adapter and test the complete link before putting it into service.
Frequently Asked Questions
Does It Include an Optical Transceiver?
Its fixed optical interface is built in. Fibre patch leads and the matching remote endpoint are selected separately.
What Fibre Does It Use?
1000BASE-SX multimode SC. 850 nm.
How Far Can the Fibre Link Run?
Up to 550 m with suitable multimode fibre. The complete optical budget includes cable, connectors, splices and the remote receiver.
Does It Supply PoE?
No. It carries Ethernet data without injecting PoE power. Power the endpoint separately or choose an appropriate separate PoE arrangement.
Can It Be Installed in a Chassis?
The manufacturer documents installation in the DMC-1000 chassis, following the board and carrier procedure for the exact converter. The chassis provides module power after installation.
Which Power Adapter Should I Use?
Use the matched supplied external DC adapter. Do not substitute an adapter based only on connector fit. Check the device label and supplied adapter voltage before connecting power.
사양
D-Link DMC-700SC Gigabit Multimode SC Fibre Media Converter
The DMC-700SC is a Gigabit media converter connecting 1000BASE-T copper Ethernet to 1000BASE-SX multimode SC. The fixed optical interface must match the fibre type and remote endpoint. The unit supports full-duplex Ethernet and provides local power and link indicators. Use a matched external power adapter and the documented installation procedure. Fibre distance is subject to the complete optical budget and the supplied hardware configuration.
| Specification | Details |
|---|---|
| Media and Interfaces | |
| Copper Port | 1 × 1000BASE-T RJ-45 |
| Optical Interface | 1000BASE-SX multimode SC |
| Wavelength | 850 nm |
| Fibre Reach | Up to 550 m with suitable multimode fibre |
| Copper Cable | Suitable Category 5 or better channel up to 100 m |
| Duplex | Full-duplex at 1000 Mbps |
| PoE Output | Not provided |
| Operation and Installation | |
| Function | Copper-to-fibre media conversion |
| Optical Endpoint | Match fibre type, wavelengths and link budget |
| Status LEDs | Power and Link/Activity |
| Deployment | Standalone or documented DMC-1000 chassis procedure |
| External Power | Use the matched supplied external DC adapter |
| Chassis Service | Follow the exact converter and carrier instructions |
| Physical and Environmental | |
| Dimensions | 120 × 88 × 25 mm |
| Device Weight | 302 g |
| Operating Temperature | 0–40°C |
| Storage Temperature | −25–70°C |
| Humidity | 10–90% RH, non-condensing |
| Warranty | 5 years |