Insta360 2-in-1 Invisible Selfie Stick and Tripod

Move from a Handheld View to a Stationary Shot Keep two useful recording arrangements in one accessory. Insta360 2-in-1 Invisible Selfie Stick and Tripod extends for handheld framing, then opens its built-in legs when a supported stationary setup suits the scene. The aluminium-alloy design retracts for carrying between locations and uses a standard 1/4-inch screw at the top. Prepare the surface, camera interface and viewpoint before recording, whether you want to include yourself in the frame or establish a more deliberate fixed composition. Highlights Handheld selfie stick and built-in tripod in one design. Extends to 105 cm with the tripod legs folded. Retracts to 24 cm for carrying. Approximately 216 g with aluminium-alloy construction. Standard 1/4-inch top screw; correct camera adapters remain necessary. Key Features Change the Support to Suit the Scene Use the accessory in the hand when you want to change position, then open the built-in tripod legs for a stationary recording. The two arrangements serve different purposes: handheld movement follows the scene, while a stable fixed position lets you step into the composition. Check the complete assembly whenever you change between them. Choose the Reach for the Composition The stick extends to 105 cm with its tripod legs folded and retracts to 24 cm. Select the useful extension for the camera angle and surrounding conditions. A longer lever arm is a different setup from a short handheld grip, so avoid treating maximum extension as the default for every shot. Let Compatible 360 Capture Conceal the Shaft With a compatible 360 camera and correct alignment, stitching can remove the selfie-stick shaft from the recorded image. This does not mean that every tripod leg, mount or accessory will disappear. Conventional wide-angle recording needs its own framing, and the result remains dependent on the camera and recording mode. Use the Intended Camera Connection The top has a standard 1/4-inch screw. Ace-series cameras require their compatible Quick Release Mount or 3-Prong to 1/4-inch Adapter. GO Ultra requires the dedicated GO Ultra Quick Release Mount. These interfaces are separate equipment; a camera appearing in a product photograph does not mean it is included. Prepare a Stable Surface Place the opened tripod on a level, stable surface with the legs positioned as instructed. Check the camera fastening and balance before stepping away, and use particular care outdoors or where wind or people could disturb the setup. The integrated legs are a support arrangement, not a guarantee of stability in every environment. Carry and Care for the Mechanism The stated 216 g weight and 24 cm retracted length describe the accessory itself. Close the legs and retract the stick as instructed before carrying it. Keep the moving sections clean, avoid forcing the mechanism and follow the manufacturer’s rinsing and drying guidance after suitable wet use. Summary Choose the 2-in-1 design when a handheld viewpoint and an occasional fixed shot belong in the same recording session. Match the camera interface, set the useful extension and give the tripod a stable surface. The accessory combines two physical supports while keeping camera functions, invisible-stitching results and placement conditions distinct. Frequently Asked Questions Does It Include a Built-In Tripod?ExpandCollapse Yes. The legs open from the accessory for a supported stationary setup and fold away for handheld use and carrying. Follow the assembly instructions and confirm the surface, balance and camera fastening before recording. How Long and Heavy Is It?ExpandCollapse The manufacturer specifies 24 cm retracted and 105 cm extended with the tripod legs folded. The accessory weighs approximately 216 g. These measurements exclude the camera and any separate camera-specific interface. Which Mounting Point Does It Have?ExpandCollapse It has a standard 1/4-inch screw at the top. The manufacturer specifies no screw at the bottom. Do not assume it can be stacked onto another tripod or support through a lower threaded connection. Do Ace-Series Cameras or GO Ultra Need Another Mount?ExpandCollapse Yes. Ace, Ace Pro and Ace Pro 2 use a compatible Quick Release Mount or 3-Prong to 1/4-inch Adapter, sold separately. GO Ultra requires its dedicated Quick Release Mount. Check the interface for the actual camera before ordering. Will the Entire Tripod Disappear in 360 Footage?ExpandCollapse No universal result is promised. Compatible 360 stitching can conceal a correctly aligned selfie-stick shaft. Tripod legs, camera fittings or other objects can remain visible, and conventional wide-angle recording does not provide the same automatic effect. Magbasa pa